5×20mm 快断保险丝 UL CSA CQC 100mA-20A 125V/250V

1.規格型號和安規認證

MODEL NUMBER AND SAFETY CERTIFICATION

品名規格：系列號+額定電流+額定電壓+認證符號

Model Number: Part Number+Rated Current+Rated Voltage+Approvals.

例子[example]:

       5GFU，        2A，         125V/250V

1)系列號 Part Number，2)額定電流 Rated Current，3)額定電壓 Rated Voltage 

1-2 額定電流和額定電壓                Rated Current And Voltage

    額定電流：32mA~20A              Rated Current: 32mA~20A

    額定電壓：125V/250V AC            Rated Voltage:125V/250V AC

1-3 標示 Marking

    保險絲上需有下列標示       The fuse shall have the following marking:

規格：特性符號+額定電流+額定電壓   Specification:Characteristic Symbol+Rated Voltage

32mA~800mA : _mA125V/250V   1A~20A: _A125V/250V

Trade mark:The Manufacture’s Logo+Part Number+Approvals 

 32mA~20A:

注意：對標示字樣大小沒有規定

Note:Size of the markings have not be specified.

2.適用範圍  SCOPE

適用於一般電子設備。Used in electronic equipment. 

3.工程圖和結構  OUTLINE DRAWING AND STRUCTURE

3-1 工程圖（單位：mm）Outline Drawing and Dimensions(Unit:mm)

3-2 結構 Structure

4.外觀及形狀；APPE***NCES AND CONFIGURATION

4-1 外觀：不應有破碎、明顯的汙斑；Appearances:There shall no fragmentation and of remarkable blotch.

4-2 形狀：帶腳的保險絲；Configuration:Axial Leaded Fuse.

5.物理特性；PHYSICAL CH***CTERISTIC

5-1 拉力測試;沿端子的軸向施加 10N 的拉力，持續 1 分鐘。

Tensile test;Keep pulling the cap of the fuse with 10N at axial

6.電氣特性

ELECTRICAL CH***CTERISTICS

熔斷/電流特性：

Pre-Arcing Time/Current Characteristic

a、Breaking capacity（分断能力）(Time Lag and Fast Acting)

      3-100A           250V             AC

b、Electrical characteristics

美标（UL）

c、Temperature character

当100%的电流下温度上升不超过75℃

When 100% of rating the temperature rise doesn’t exceed 75℃.Average Time Current Curves

Average Time Current Curves

7.環境特性

 ENVIRonMENTAL SPECIFICATION

7-1 操作溫度範圍：-5℃~60℃

Operating Temperature: -5℃~60℃

7-2 保存條件

Storage Conditions

溫度：+10℃~60℃

Temperature: +10℃~60℃

在相對濕度≤75%下平均可存放3年

On average, It can be stored below the relative humidity or 75% for 3 years.

在非露天下，相對濕度為95%下多可存放30天。

Without dew, It can be kept under humidity of 95% for 30 days.

8.焊接條件

SOLDERING PAAMETERS

8-1波峰焊

Wave Solder

焊接溫度：260±5℃

Soldering Temperature:260±5℃

焊接時間：4 Sec. Max.

Soldering Time:4 Sec.Max.

8-2手工焊錫

Manual Solder

焊接溫度：350±5℃

Soldering Temperature: 350±5℃

焊接時間：3 Sec. Max.

Soldering Time: 3 Sec. Max.

9.其他使用注意事項

OTHER NOTICE IN USING

如果需在保險絲上加熱縮套管，烘烤溫度與時間需參照以下規定

If heat shrink tubing was needed,the roast temperature and time should be refer to the following.

設定烘烤溫度：不大於150℃  烘烤時間：50s Max.

The temperature should be sel under 150℃,roast time:50s Max.