珠海飞宇光电科技有限公司始建于2005年,公司座落在深圳,主厂区占地3000多平方米,职工200人。公司通过吸引国内外先进的技术与自主研发相结合,不断新。主要生产WDM波分复用器、SFP/SFP+/XFP/QSFP光模块等。多项产品获得国家发时、使用新型专利。公司拥有先进的制造设备和完善的检测手段。光功率计、OSA、光插回损仪、误码仪、眼图仪、高低温循环箱等进近百台专业精密制造设备与检测设备。为客户提供优质的产品,并可以按客户的要求设计加工。
111
公司座落在深圳,主厂区占地3000多平方米,职工200人,公司拥有省级研发技术中心一个,其中工程师20人,公司通过吸引国内外先进的技术与自主研发相结合,不断创新。主要生产WDM波分复用器、SFP/SFP+/XFP/QSFP光模块。多项产品获得国家发时、使用新型专利。
111
111
111
111
所有产品上架型号均是长期生产型号,现货产品一般3个工作日内发出,订做产品一般7-15个工作日内完工发出,买家在购买前请先和我们销售经理联系,确认是否有现货,由于各地办事处同时销售,库存量变化比较大,为了防止可能缺货给您带来的困扰,具体出货时间请咨询销售经理。
运输时间:物流运输一般2-7天,由于物流公司不在我们控制范围内,外加上天气、交通路况等特殊原因,可能会有发货、到货延时,请多包涵、谅解。
详情可以或QQ联系,客户交流可以在此群进行技术交流:
:
QQ: 3203701634
Q群: 369512327
FYPPC-XX96-40BD
10Gb/s CWDM SFP+ 40km Transceiver
SFP+波分模块,可直接用在交换机10G光口上,应用在WDM波分复用系统,完美搭配我公司波分复用器,同时兼容华为、中兴波分复用系统。发光功率和接收灵敏度有保证。可以顺带咨询波分系统配置。
Product Features
l Up to 11.1Gbps Data Links
l Up to 40km transmission on SMF
l Power dissipation
l Uncooled CWDM DFB Laser and PIN receiver
l Metal enclosure, for lower EMI
l 2-wire interface with integrated Digital Diagnostic monitoring
l Hot-pluggable SFP+ footprint
l Specifications compliant with SFF 8472
l Compliant with SFP+ MSA with LC connector
l Single 3.3V power supply
l Case operating temperature range:0°C to 70°C
Applications
l 10GBASE-LR/LW 10G Ethernet
Standard
l Compliant to 802.3ae 10GBASE-LR/LW
l Compliant to SFF-8431
l RoHS Compliant.
Product selection
FYPPC-XX96-40BD
Wavelength xx Wavelength xxOptical Characteristics
Parameter | Symbol | Min | Typ | Max | Unit | NOTE |
Transmitter |
|
|
|
|
|
|
Output Opt. Pwr | POUT | -1 |
| 3 | dBm | 1 |
Optical Wavelength | λ | λ-6.5 |
| λ+6.5 | nm | 2 |
Spectral Width (-20dB) | σ |
|
| 1 | nm |
|
Optical Extinction Ratio | ER | 3.5 |
|
| dB |
|
Transmitter and Dispersion Peanlty | TDP |
|
| 3 | dB |
|
Side mode Supression ratio | SMSR | 30 |
|
| dB |
|
RIN | RIN |
|
| -128 | dB/Hz |
|
Output Eye Mask |
| Compliant with IEEE 802.3ae |
| |||
Receiver |
|
|
|
|
|
|
Receiver Sensitivity | Psen |
|
| -15 | dBm | 3 |
Input Saturation Power (Overload) | PSAT | 0.5 |
|
| dBm |
|
Input Optical Wavelength | λIN | 1270 |
| 1610 | nm |
|
LOS -Assert Power | PA |
|
| -17 | dBm |
|
LOS -Deassert Power | PD | -30 |
|
| dBm |
|
LOS -Hysteresis | PHys | 0.5 |
|
| dB |
1. Class 1 Laser Safety per FDA/CDRH and IEC-825-1 regulations.Notes:
2. λ”is:1270,1290,1310,1330,1350,1370,1390,1410,1430,1450, please the “product selection” .
3. Measured with a PRBS 231-1 test pattern, @10.325Gb/s, BER
Electrical Characteristics
Parameter | Symbol | Min | Typ | Max | Unit | NOTE |
Supply Voltage | Vcc | 3.14 | 3.3 | 3.46 | V |
|
Supply Current | Icc |
|
| 350 | mA |
|
Transmitter |
|
|
|
|
|
|
Input differential impedance | Rin |
| 100 |
| Ω | 1 |
Differential data input swing | Vin,pp | 180 |
| 1200 | mV |
|
Transmit Disable Voltage | VD | Vcc–1.3 |
| Vcc | V |
|
Transmit Enable Voltage | VEN | Vee |
| Vee+ 0.8 | V | 2 |
Transmit Disable Assert Time |
|
|
| 10 | us |
|
Receiver |
|
|
|
|
|
|
Differential data output swing | Vout,pp | 300 |
| 850 | mV | 3 |
Data output rise time | tr | 30 |
|
| ps | 4 |
Data output fall time | tf | 30 |
|
| ps | 4 |
LOS Fault | VLOS fault | Vcc–1.3 |
| VccHOST | V | 5 |
LOS Normal | VLOS norm | Vee |
| Vee+0.8 | V | 5 |
Power Supply Rejection | PSR | 100 |
|
| mVpp | 6 |
Notes:
1. Connected directly to TX data input pins. AC coupled thereafter.
2. Or open circuit.
3. Input 100 ohms differential termination.
4. These are unfiltered 20-80% values
Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.
6. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network.
Diagram of Host Board Connector Block Pin Numbers and Name
Pin | Symbol | NOTE | |
1 | VEET | Transmitter Ground (Common with Receiver Ground) | 1 |
2 | TFAULT | Transmitter Fault. | 2 |
3 | TDIS | Transmitter Disable. Laser output disabled on high or open. | 3 |
4 | SDA | 2-wire Serial Interface Data Line | 4 |
5 | SCL | 2-wire Serial Interface Clock Line | 4 |
6 | MOD_ABS | Module Absent. Grounded within the module | 4 |
7 | RS0 | Rate Select 0 | 5 |
8 | LOS | Loss of Signal indication. Logic 0 indicates normal operation. | 6 |
9 | RS1 | No connection required | 1 |
10 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
11 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
12 | RD- | Receiver Inverted DATA out. AC Coupled |
|
13 | RD+ | Receiver Non-inverted DATA out. AC Coupled |
|
14 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
15 | VCCR | Receiver Power Supply |
|
16 | VCCT | Transmitter Power Supply |
|
17 | VEET | Transmitter Ground (Common with Receiver Ground) | 1 |
18 | TD+ | Transmitter Non-Inverted DATA in. AC Coupled. |
|
19 | TD- | Transmitter Inverted DATA in. AC Coupled. |
|
20 | VEET | Transmitter Ground (Common with Receiver Ground) | 1 |
Notes:
1. Circuit ground is internally isolated from chassis ground.
2. TFAULT is an open collector/drain output, which should be pulled up with a 4.7k – 10k Ohms resistor on the host board if intended for use. Pull up voltage should be between 2.0V to Vcc + 0.3V.A high output indicates a transmitter fault caused by either the TX bias current or the TX output power exceeding the preset alarm thresholds. A low output indicates normal operation. In the low state, the output is pulled to
3. Laser output disabled on TDIS >2.0V or open, enabled on TDIS
4. Should be pulled up with 4.7kΩ- 10kΩ host board to a voltage between 2.0V and 3.6V. MOD_ABS pulls line low to indicate module is plugged in.
5. Internally pulled down per SFF-8431 Rev 4.1.
6. LOS is open collector output. It should be pulled up with 4.7kΩ – 10kΩ on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
Digital Diagnostic Functions
Flyin FYPPC-XX96-40BD transceivers support the 2-wire serial communication protocol as defined in the SFP+MSA.
The standard SFP serial ID provides access to identification information that describes the transceiver’s capabilities, standard interfaces, manufacturer, and other information.
Additionally, Flyin SFP+ transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range.
The SFP+ MSA defines a 256-byte memory map in EEPROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h).The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged.
The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially.
Regulatory Compliance
Feature | Reference | Performance |
Electrostatic discharge(ESD) | IEC/EN 61000-4-2 | Compatible with standards |
Electromagnetic Interference (EMI) | FCC Part 15 Class B EN 55022 Class B (CISPR 22A) | Compatible with standards |
Laser Eye Safety | FDA 21CFR 1040.10, 1040.11 IEC/EN 60825-1,2 | Class 1 laser product |
Component Recognition | IEC/EN 60950 ,UL | Compatible with standards |
ROHS | 2002/95/EC | Compatible with standards |
EMC | EN61000-3 | Compatible with standards |
Ordering information
Part Number | |
FYPPC-XX96-40BD | Uncooled CWDM DFB Laser, 10Gbps, 40km, 0ºC ~ +70ºC, DDM |
-------------------------------------------------------------
更多产品:
更多产品:szflyin.net114.com/
详情可以或QQ联系,客户交流可以在此群进行技术交流:
:
QQ: 3203701634
Q群: 369512327
免责声明:当前页为 Flyin 飞宇 FYPPC-XX96-40BD CWDM系统专用,彩光模块产品信息展示页,该页所展示的 Flyin 飞宇 FYPPC-XX96-40BD CWDM系统专用,彩光模块产品信息及价格等相关信息均有企业自行发布与提供, Flyin 飞宇 FYPPC-XX96-40BD CWDM系统专用,彩光模块产品真实性、准确性、合法性由店铺所有企业完全负责。世界工厂网对此不承担任何保证责任,亦不涉及用户间因交易而产生的法律关系及法律纠纷,纠纷由会员自行协商解决。
友情提醒:世界工厂网仅作为用户寻找交易对象,就货物和服务的交易进行协商,以及获取各类与贸易相关的服务信息的渠道。为避免产生购买风险,建议您在购买相关产品前务必确认供应商资质及产品质量。过低的价格、夸张的描述、私人银行账户等都有可能是虚假信息,请您谨慎对待,谨防欺诈,对于任何付款行为请您慎重抉择。
投诉方式:fawu@gongchang.com是处理侵权投诉的专用邮箱,在您的合法权益受到侵害时,请将您真实身份信息及受到侵权的初步证据发送到该邮箱,我们会在5个工作日内给您答复,感谢您对世界工厂网的关注与支持!